Pacemaker Boats

As you said "I's much rather work on it in the head as oppossed to flopping around on the galley floor in a boater's contortion reaching around in the bilge"

That is 1 of the reasons. 2nd is the dr ...

the pump itself it mounted in the cabinet.

1 hose runs overboard

1 hose runs (ran) behind the cabinet
down towards the bildge. Just before
the bildge there is a small bulkhead
where the hose ...

Does anyone know the height under the shower pan
of a 32 foot fly bridge?

I want to cut the shower pan, install a rule
slump pump and then fiberglass back over.

I'm just wondering if the rule ...

I'd like to put in a rule slump pump under the shower pan

Does anyone know how much height is under the pan?

The rule pump need about 5 1/2 - 6 inches.

They could have made the drain piping a ...

Both..

There were no "o" rings on the cap itself
and the one on the fill tube was shot.

I had the engine mech. out yesterday...

Turns out the seal on the fuel fill had gone
bad and allowed to much water into the tank.

And as far as the cross-over line...

I just didn't understan ...

Thanks Leo...

This boat is used for full time crusing, that is
why I need the fuel. It will do 24 knots with
both 350's running... $$$$

So we want to run about 6-8 knots off of
just one eng ...

Looks like there may be a lot
of things I'll need to change,
over time.

I'm seeing all valves open...
there appears to be a cross-over
line, but I think I need to take
a closer look today.

...

It looks like I have the same setup
as yours, that needs to be changed.

Please let me know what you used and how you were
able to do it, as I will be wanting the same.

Also, during transfer w ...

it appears that is the way it is setup...
however (call me dumb, its ok) the
fuel does not appear to be being
drawn from the other tank.

The 2nd reason I'd like to be able to
hit a switch to tr ...

Hello All,

Does anyone know of an easy setup
to transfer fuel (gas) between tanks.

Currently it does not appear my starboard
engine is drawing fuel from my port tank,
when only the starboard ...

Hello all,

I just picked up a 76 32' flybridge.

I am looking to add a rear deck off
the Flybridge.

Has anyone done such a project?

I want to use Alumstock for the structure.
Then over ...

Well... I replaced the 3 main "in-line" fuel filters, one for each tank. The engines are running real good. Next month, after running the engines for 20 to 30 hours, I'll again replace those filter ...

I like both ideas...

but being here on jew fish creek, i won't be able to look at your's or terry's until monday. trying to work on a boat here on the weekend is taking your life into a place i do ...

well that sounds like 2 easy things for me to do tomorrow. The port engine does show a different vac. at the same rpms as the star.

And it wasn't the 2 I was thinking of so that a REALLY good thin ...

Hello all,

I've got fairly new (less then 300 hrs) 350 crusaders (265 hp).

The port engine starts up fine.

But 1) it will not stay running if under 700 rpms.
2) If I put it at say 1400 ...

On my 32', the water tank is located "somewhere" under the galley floor.

My wife just sanded, cleaned, and put new tile down... hinesite says I should have looked for any screws (covered or otherw ...

I took (my wife did ) off all the old tile but did not see
a hatch that would life up. I'm used to sailboats where you
can see and just lift the hatch off.

I'd never heard of screwing a floor do ...

Hello all,

I just picked up a 76 32' flybridge.

Does anyone either have or know where
I can get copies of all the specs, layout,
etc.

thanks

We just picked up a 76 32' flybridge...

Will someone PLEASE tell me how to access the water tank.

And does anyone know how and where to locate another 1 or 2 30 gal tanks?

We just picked up a 76 32 flybridge... will someone PLEASE tell me how you gain access to the water tank?